| NO. | Name | Description |
| 1 | Mud agitator | JNB-15KW, ZJW-15, with elect motor 15kw,1440rpm,50hz, 380v |
| 2 | pressure transducer | YPQ-400B, for FKQ6406 remote control unit |
| 3 | gear shaft | 01-02-20M, for power tong ZQ203-125II |
| 4 | Brush carbon for D/C motor | T900 (25C14076P01, 41B537963P01) |
| 5 | hydraulic Gate valve | 4 1/16", 10000 psi, flanged end, pff103-70 |
| 6 | manual gate valve for chock manifold | 4 1/16", 10000 psi, zf103-70 |
| 7 | repair kit for manual gate valve | 4 1/16", 10000 psi, zf103-10 |
| 8 | manual gate valve for chock manifold | 2 9/16", 10000 psi, zf65-70 |
| 9 | repair kit for manual gate valve | 2 9/16", 10000 psi, zf65-70 |
| 10 | hydraulic adjustable chock valve | 2 9/16", 10000 psi, yjf-65-70 |
| 11 | manual gate valve for chock valve | 4 1/16", 5000 psi, zf103-35 |
| 12 | 5" jaw roller | 19.100-19 |
| 13 | pin for jaw | 19.100-24 |
| 14 | 5" jaw | 19.100-15 |
| 15 | 3 1/2" jaw | 19.100-13 |
| 16 | 8” jaw | 19.100-17 |
| 17 | pneumatic clutch | 19.310.00 |
| 18 | 4 1/2" jaw | 19.100-14 |
| 19 | 3 1/2" roller | 19.100-18 |
| 20 | location lump | 19.100-02, 19.100-03, 19.100-04, 19.100-06 |
| 21 | sand pump (XBSY) | SB 6X8 zj-12 1/2"with elect motor, 55kw, 1440rpm, 50hz, 380v |
| 22 | water pump | IS 80-65-160, 2900rpm |
| 23 | rubber hose | 12", 6m length, -145psi, for single line |
| 24 | hose | 4", 5000 psi, 4 mtr length, w/4”welded hammer union, 1002 fig， male one side, and femal the other |
| 25 | rubber hose | 2", 5000 psi, 10 mtr length, w/welded hammer union, 1502 fig, male one side, and female the other |
| 26 | push botton shift selector | 29541005 |
| 27 | sprocket for hydraulic brake ssc502 | sca502-03 |
| 28 | cover for hydraulic brake ssc502 | LTH1177 |
| 29 | mud gas separator | BWZYQ1000 |
| 30 | wood steel rig matting board | L:500cm, W:198cm, H: 16cm |
| 31 | wood steel rig matting board | L:400cm, W: 198cm, H:16cm |
| 32 | plug | 200A, 200YT |
| 33 | die | ZQ203-100 |
| 34 | DC power box for crown protector | GLFP-IIB-04 |
| 35 | filter | AH100101190200 |
| 36 | liner 170mm | 3NB-1300 |
| 37 | seal | 107.11.110.05, 3NB-1300 |
| 38 | hose | 2", 5000 psi, 9mtr length, welded ends, male at one side, femal at the other |
| 39 | conflex hose | 4 1/16", 10000 psi, flanged type, 30mtr length |
| 40 | air control line 23 head air cable | accumulator model: FKQ6406 |
| 41 | anti collision with english soft ware | ZSF-10D, Ver: 04-10, input:220v, output: 24v. |
| 42 | bearing | 2097128 |
| 43 | hydraumatic break for draw work type JC21/11 | SSC502 |
| 44 | complete engine | 6135k-9a |
| 45 | jaw plate frame | 12AZ-104 |
| 46 | insert for jaw rack | 19.100-01 |
| 47 | jaw rack | 19.100-10 ZQ203-125II |
| 48 | pin | A6X16 GB119-86 ZQ203-125II |
| 49 | repair kit for pressure regulating valve - Sullair | 250019-453 |
| 50 | blow down valve-sullair | 02250100-042 |
| 51 | repair kit for control solenoid valve | 02250157-500 |
| 52 | Hinged casing spider | 200 tons, size to 13 3/8", pn: 7704-A-79 |
| 53 | insert for casing spider | 7"-8 5/8", pn: 7704-A-81 |
| 54 | insert for casing spider | 9-10 3/4", pn: 7704-A-30 |
| 55 | pully assy | AA18004-03.00/ AA315101-03.00 |
| 56 | drilling line | 6X19 IWRC, 1960EIPS, UNG, LHO, MBL 46.9T 2000MTR,LEFT LAY |
| 57 | cooling water tank for drawworks | 20m/3, motor capacity 15kw, rate flow 100m3/h, pump lift:32m |
| 58 | hydraulic power tong | XYQ 12A from 2 7/8" to 5 1/2" |
| 59 | raising line | 48 mm x 52.8m construction 6x49sws+iwrc eeip, right |
| 60 | 4 pin drive master bushing | 105.08.70.00 |
| 61 | hydraulic cutter for drilling line | 1 1/4" |
| 62 | bladder for koomery | FKQ6406-8 |
| 63 | drill pipe elevator | DDZ |
| 64 | SDML slips | 2 7/8" drill pipe |
| 65 | travelling block anti collision system | imput: 220V/AC, output:24V/DC |
| 66 | tubing power tong assy | XYQ3B/3C |
| 67 | packing element | 13 5/8" 5000psi, FH35-35 ANNULAR |
| 68 | singel shoot electronic inclinometer | HKCX-X-DDF |
| 69 | chain roller | 32S-2 X 400 PITCH |
| 70 | air tube | for clutch 1070/200 |
| 71 | drill coller slips | DCS-L 8"-9 1/2" |